NewKiwee PoE over Coax Kit · MoCA 2.5

PoE over Coax at 2.5 Gbps.

Power and multi-gig Ethernet for a security camera or Wi-Fi access point, over the coax already in your walls. No new Ethernet run. No outlet at the device.

Complete kit · Head-End + Remote
Kiwee Broadband PoE over Coax adapter kit: black KB-P3-01H Head-End and white KB-P3-01R Remote Unit
Rear ports of the Kiwee PoE over Coax kit: MoCA PoE IN and PoE+ OUT on the Remote; MoCA NO PWR, MoCA PoE OUT, PoE++ IN, RESET and DC on the Head-End
How PoE over Coax works: the Head-End at the router sends 30W PoE+ power and 2.5 Gbps data over one coax cable to the Remote at the camera or access point
30W PoE+, 2.5 Gbps MoCA 2.5 speed, up to 980 ft over a single coax cable and smart power detection
PoE over Coax use cases: analog CCTV to IP camera upgrade, security camera without an outlet, Wi-Fi access point where coax reaches
Set up the PoE over Coax kit in 3 steps; Head-End, Remote, 48V adapter, Ethernet and coax cables and F-BNC adapters included
Know your ports: MoCA NO PWR, MoCA PoE OUT, PoE++ IN, RESET and DC on the Head-End; MoCA PoE IN and PoE+ OUT on the Remote; POWER, MoCA and PoE LEDs
Complete kit, ready to installHead-End + Remote, 48 V adapter, cables and BNC adapters

See today’s price and delivery date on Amazon.

  • Fulfilled by Amazon
  • 30-day returns
  • 1-year warranty
  • FCC & CE
  • 2.5 GbpsMoCA 2.5 speed
  • 30 W PoE+IEEE 802.3at
  • Up to 980 ft*300 m on one coax run

*About 650 ft (200 m) out of the box in MoCA D-band. Up to about 980 ft (300 m) with the free E-band firmware, on coax with no cable TV or cable internet.

  • 25× faster

    Up to 2.5 Gbps with MoCA 2.5, versus 100 Mbps for typical coax converters

  • 3× the reach

    Up to 980 ft (300 m)* on one coax run, versus 328 ft (100 m) for an Ethernet cable

  • 0outlets

    Needed at the camera or access point: 30 W PoE+ arrives over the coax

  • 10min setup

    No tools, no app and no configuration

PoE over coax, explained

What is PoE over coax?

PoE over coax sends Ethernet data and Power over Ethernet (PoE) through a coaxial cable instead of a Cat5e or Cat6 cable. An adapter at each end converts between Ethernet and coax, so a security camera or Wi-Fi access point gets both its network connection and its power from the coax already in your walls.

The Kiwee PoE over Coax Kit (KB-P3-01) does this with MoCA 2.5: up to 2.5 Gbps of data and up to 30 W of IEEE 802.3at PoE+ on a single coax run of up to 980 ft (300 m). The same setup is also called Ethernet over coax with PoE, a coax-to-Ethernet adapter with PoE, or a PoE over coax extender.

At a glance

Product
Kiwee PoE over Coax Kit KB-P3-01: Head-End KB-P3-01H + Remote KB-P3-01R
Data
Up to 2.5 Gbps over MoCA 2.5, with a 2.5GbE port on each unit
Power
PoE+ IEEE 802.3at: 30 W at the port, 25.5 W at the device
Range
About 650 ft (200 m) in D-band, 980 ft (300 m) with the E-band firmware
Coax
RG6 or RG59 with F-type connectors; F-to-BNC adapters included
Head-End power
Included 48 V adapter or a PoE++ (802.3bt) switch port
Powers
IP and PTZ cameras, Wi-Fi 6, 6E and 7 access points, VoIP phones
Compliance
FCC Class B (US) and CE (EU); 1-year warranty

PoE over coax use cases

If coax reaches it, you can power it.

Most homes and small businesses already have coax running to the places you want a camera or access point. This kit turns that cable into a PoE+ Ethernet link: no drilling, no new cable, no electrician.

Illustration: analog CCTV camera replaced by an IP camera on the same coax with a BNC adapter
Analog to IP

CCTV upgrade

Swap an old analog camera for a 4K IP camera on the same RG59 or RG6 cable. Two F-to-BNC adapters are in the box.

Illustration: security camera on a garage powered through the coax in the wall
No outlet needed

Security camera

Power a PoE camera on the garage, the eaves or a detached building through the coax in the wall.

Illustration: ceiling Wi-Fi access point powered over coax in a home office
Multi-gig backhaul

Wi-Fi access point

Mount a Wi-Fi 6, 6E or 7 access point wherever coax reaches and give it a 2.5 Gbps wired backhaul.

Popular spots

  • Garage
  • Attic
  • Basement
  • Eaves & porch
  • Detached shop
  • Barn
  • Home office
  • Upstairs bedroom

How PoE over coax works

Two units. One coax. Power and data together.

The Head-End sends power and data down the coax. The Remote turns them back into a standard PoE+ Ethernet port.

  1. 1

    At your router

    The black Head-End connects to your router or switch and runs on the included 48 V adapter, or on a PoE++ switch port.

  2. 2

    Through your coax

    It sends 48 V and MoCA 2.5 data down a single coax run. Power switches on only after the Remote is detected.

  3. 3

    At the device

    The white Remote delivers Ethernet with PoE+ up to 30 W. Your camera or access point powers up on its own.

Kiwee PoE over Coax Kit features

Built for the jobs 100 Mbps converters can’t do.

MoCA 2.5 speed, real PoE+ power and safety features that make sense on the coax already in your home.

Smart power detection

The powered port sends 48 V only after it detects the Kiwee Remote on the coax. Plug in anything else by mistake and the port stays off.

Kiwee Remote detected48 V ONTV, modem or analog camera only0 V

2.5 Gbps, not 100 Mbps

MoCA 2.5 with a 2.5GbE port on each unit. Room for a Wi-Fi 7 access point or several 4K camera streams.

Typical coax converter100 Mbps
Kiwee MoCA 2.52.5 Gbps

30 W PoE+

IEEE 802.3at, compatible with 802.3af. Up to 25.5 W at the device, enough for PTZ cameras and many Wi-Fi 7 access points.

Basic PoE (802.3af)15.4 W
Kiwee PoE+ (802.3at)30 W

Two ways to power

Use the included 48 V adapter or a PoE++ (802.3bt) switch port. Connect both for automatic backup: DC takes priority.

Joins your MoCA network

A second, unpowered coax port links the kit to MoCA 2.5 adapters such as the KB-M3-02 and KB-M3-03.

Up to 980 ft (300 m) on one coax run

About 650 ft (200 m) out of the box in MoCA D-band. Need more? On a run with no cable TV or cable internet, the free E-band firmware stretches it to about 980 ft (300 m), three times the 328 ft (100 m) limit of an Ethernet cable.

Optional encryption

Private MoCA link for apartments and shared buildings.

CCTV-ready

F-type ports plus two F-to-BNC adapters in the box.

Plug and play

No app, no pairing. Linked within a minute.

FCC & CE

Meets FCC Class B (US) and CE (EU) requirements for home use.

PoE over coax vs. Ethernet over coax vs. Cat6

The faster way to put PoE on coax.

How the Kiwee kit stacks up against a typical 10/100 coax converter and pulling a new Ethernet cable.

Kiwee PoE over Coax Kit compared with a typical 10/100 Ethernet over coax converter and a new Cat6 cable
FeatureKiwee PoE over CoaxKB-P3-01 · MoCA 2.5Typical coax converter10/100 Ethernet over coaxNew Ethernet cableCat6 run
Top speed2.5 Gbps100 MbpsUp to 10 Gbps
Uses your existing coaxYesYesNew cable to pull
Power at the devicePoE+ up to 30 WVaries by modelNeeds a PoE switch or injector
Distance per runUp to 980 ft (300 m)Varies by model328 ft (100 m) maximum
Works with a MoCA networkSecond coax portUsually notNot applicable
InstallationAbout 10 minutes, no toolsMinutesDrilling and cable pulling

Range depends on cable quality and connectors. 2.5 Gbps requires 2.5GbE ports on your switch and device.

Get 2.5 Gbps and PoE+ on the coax you already have.Both units included · Fulfilled by Amazon · 30-day returns
Buy on Amazon (opens in a new tab)

How to install PoE over coax

Up and running in about 10 minutes.

No tools, no app, no configuration. Connect the Remote first, then the Head-End.

  1. Coax into MoCA PoE IN and the camera into PoE+ OUT on the white Remote Unit

    Connect the Remote

    Coax into MoCA PoE IN. Your camera or access point into PoE+ OUT.

  2. Coax cable going into the MoCA PoE OUT port of the black Head-End

    Connect the Head-End

    Your coax into MoCA PoE OUT, the powered port. Ethernet from your router into PoE++ IN.

  3. Ethernet from the router into PoE++ IN and the 48V adapter into DC on the Head-End

    Power it on

    Plug the 48 V adapter into DC, or use a PoE++ switch port. POWER and MoCA light up within a minute.

Keep the powered run direct. Any splitter between the two units must be DC-pass (power-passing). Amplifiers, diplexers and satellite multiswitches block power and must be removed from that run.

PoE over coax compatibility

Will it work for you? Check in 30 seconds.

Four quick questions about your coax and your device. Your result updates as you answer.

What’s on the coax between the two spots?

The kit needs one coax run from your router area to the device spot. Amplifiers, diplexers and satellite multiswitches block its power, and any splitter must be DC-pass.

How long is that run, roughly?

About 650 ft (200 m) out of the box and about 980 ft (300 m) with the free E-band firmware, on RG6. RG59 from old CCTV systems reaches less far.

Is satellite TV on that cable?

Satellite receivers send their own power up the coax. Cable TV and cable internet can share the run in D-band with DC blocks.

What will you connect?

Any standard PoE device (802.3af/at, Class 0 to 4) up to 25.5 W. The Remote is an indoor unit.

Your result0 of 4 answered

Answer four quick questions

Your result appears here as you go. What the kit needs:

  • One direct coax run, DC-pass splitters only
  • Up to 980 ft (300 m) on RG6
  • No satellite TV on that cable
  • A PoE device up to 25.5 W, or any device for data only

Looks like a great match

Your coax and your device fit what the kit needs.

Buy on Amazon (opens in a new tab)

Almost: take the amplifier off that run

Amplifiers, diplexers and satellite multiswitches block the kit’s power. Remove it from the run between the two units, or use another coax run, and you’re set.

Buy on Amazon (opens in a new tab)

Use a coax run without satellite TV

A satellite receiver sends power up the cable to the dish, and that conflicts with the kit’s 48 V. Pick another coax run, or a satellite cable you no longer use once the dish and receiver are disconnected. Not sure? Send us a photo and we’ll help.

That run is longer than one kit’s range

The kit reaches about 980 ft (300 m) on RG6 with the free E-band firmware. Email us a sketch of your setup and we’ll suggest options.

Not sure? Email us a photo

What it can power

Any standard PoE device (802.3af/at, Class 0 to 4) up to 25.5 W.

DeviceTypical powerWorks?
IP camera (fixed, dome, bullet)Class 2–3, up to 13 WYes
PTZ or heated cameraClass 4, up to 25.5 WYes, if PoE+ is enough
Wi-Fi 6, 6E or 7 access pointPoE+ (802.3at)Yes, if it runs on PoE+
VoIP phone, PoE mini switchClass 1–4Yes
PC, TV, game consoleNo PoEData only

Devices that need PoE++ (802.3bt) or passive PoE are not supported. For PoE++, see the KB-M3-04.

Ports and LEDs

Connect it right the first time.

Orange marks power, blue marks data. The powered coax port only ever goes to the Remote.

Rear panels of the Kiwee PoE over Coax kit with numbered ports: MoCA PoE IN, PoE+ OUT and RESET on the white Remote; MoCA NO PWR, MoCA PoE OUT, PoE++ IN, RESET and DC on the black Head-End

Remote KB-P3-01R · white

MoCA PoE IN
Coax from the Head-End. Receives power and data.
PoE+ OUT
2.5GbE to your camera or access point, with up to 30 W PoE+.
RESET
Hold for 10 seconds to restore factory settings.

Head-End KB-P3-01H · black

MoCA NO PWR
Data only, never powered. Optional link to your home MoCA network.
MoCA PoE OUT
Power and data to the Remote. 48 V is switched on only after the Remote is detected.
PoE++ IN
2.5GbE to your router or switch, always required. Also accepts PoE++ power.
RESET
Hold for 10 seconds to restore factory settings.
DC
Input for the included 48 V adapter.

What the LEDs tell you

  • POWEROn: the unit has power. On the Remote, power comes through the coax.
  • MoCAOn: coax link is up. Blinking: data is flowing.
  • PoE (Head-End top)On: Remote detected and 48 V sent over the coax.
  • Ethernet port LEDsHead-End: PoE++ power from your switch. Remote: left = data, right = device powered.

Specifications · KB-P3-01

PoE over Coax Kit tech specs.

Technology
MoCA 2.5, up to 2.5 Gbps
Frequency
D-band 1125–1675 MHz (default) · E-band 400–900 MHz (free firmware)
Coax ports
2 × F-type: MoCA PoE OUT (powered), MoCA NO PWR (data only)
1 × F-type: MoCA PoE IN
Ethernet
1 × 2.5GbE RJ45 (PoE++ IN)
1 × 2.5GbE RJ45 (PoE+ OUT)
Link speeds
2.5G / 1G / 100M, auto-negotiation
Power input
48 V DC adapter (included) and/or PoE++ IEEE 802.3bt Type 3/4; DC has priority
48 V DC over the coax from the Head-End
Power output
48 V DC on MoCA PoE OUT, only after the Remote is detected
PoE+ IEEE 802.3at: 30 W at the port, 25.5 W at the device (802.3af compatible)
Coax range
About 650 ft / 200 m (D-band) · about 980 ft / 300 m (E-band), on RG6
Security
MoCA link encryption, off by default
LEDs
Top: POWER, MoCA, PoE · RJ45: PoE++ IN
Top: POWER, MoCA · RJ45: data, PoE OUT
Management
Built-in web interface, default IP 192.168.144.200
Built-in web interface, default IP 192.168.144.201
Power adapter
48 V DC, 1 A; US or EU plug, depending on the marketplace
Operating temperature
32 to 131 °F (0 to 55 °C), indoor use only
Storage temperature
−4 to 185 °F (−20 to 85 °C)
Humidity
10–85% operating, 5–90% storage, non-condensing
Compliance
FCC Class B (US) · CE (EU)
Warranty
1-year Kiwee Broadband hardware warranty

What’s in the box

  • Head-EndKB-P3-01H, black
  • RemoteKB-P3-01R, white
  • 48 V power adapterUS or EU plug, by marketplace
  • 2×Ethernet cables3.3 ft (1 m)
  • 2×Coax cables3.3 ft (1 m)
  • 2×F-to-BNC adaptersFor analog CCTV coax
  • F-to-IEC adaptersEU kit, for TV wall sockets
  • User guidePrinted

Your coax run between the two locations is not included.

Downloads

Firmware

Free for both units. The kit ships in D-band. To switch to E-band for longer runs, or back again, update both units, each with its own file.

How to update
  1. Connect a computer as shown under “Web management” in the user manual (PDF, opens in a new tab).

  2. Remote first. In a browser, open 192.168.144.201 and log in. Go to Upgrade, choose the Remote file and click Upgrade. When it’s done, after 60–90 seconds, click Reboot.

  3. Then the Head-End. Repeat at 192.168.144.200 with the Head-End file. The MoCA LED lights up again once both units run the same band.

One file per unit. The Head-End (KB-P3-01H) and Remote (KB-P3-01R) files set different IP addresses, so never swap them. Don’t unplug either unit or the coax during an update: the Remote gets its power through the coax.

FAQ

PoE over coax questions, answered.

Everything buyers ask before installing PoE over coax.

Not sure your coax will work?

Send us a photo of your setup and a quick description of the run. We’ll help you check it before you order, and we usually reply within 1 business day.

info@kiwee-broadband.com
Will this work with the coax I already have?

Yes, if a single coax run connects your router area to the spot where the camera or access point goes. RG6 gives the longest reach; RG59 from older CCTV systems also works on shorter runs.

The run must be direct: remove amplifiers, diplexers and satellite multiswitches, and use only DC-pass (power-passing) splitters between the two units.

What’s included in the kit?

Both units: the black Head-End (KB-P3-01H) for your router and the white Remote (KB-P3-01R) for your camera or access point. The kit also includes the 48 V power adapter, two Ethernet cables, two coax cables, two F-to-BNC adapters and a printed user guide.

The EU kit comes with an EU-plug power adapter and adds F-to-IEC adapters for TV wall sockets.

How far can PoE over coax reach?

About 650 ft (200 m) out of the box in MoCA D-band, and about 980 ft (300 m) after installing the free E-band firmware on both units: up to three times the 328 ft (100 m) limit of an Ethernet cable. Real-world reach depends on the cable, the connectors and any splitters on the run.

Do I need the E-band firmware?

Only if your coax run is longer than about 650 ft (200 m), or to join an E-band MoCA network such as the KB-M3-02E. Out of the box, the kit runs in D-band, the only band that can share the coax with cable TV or cable internet.

To switch, update both units, the Remote first, each with its own file. The free files and the steps are in Firmware downloads. You can switch back to D-band the same way.

How fast is PoE over coax with this kit?

Up to 2.5 Gbps. MoCA 2.5 runs at up to 2.5 Gbps and each unit has a 2.5GbE port. To go beyond 1 Gbps, the router or switch on one end and the device on the other also need 2.5GbE ports. Long or thin cables, worn connectors and splitters reduce speed.

Do I need a PoE switch?

No. The included 48 V adapter powers the Head-End, so any router or switch port works. A PoE++ switch port (IEEE 802.3bt Type 3 or Type 4) can power the Head-End instead; a PoE+ (802.3at) port does not supply enough power.

Either way, the Head-End‘s Ethernet connection to your router or switch is required.

What devices can I power over coax?

Standard PoE devices (IEEE 802.3af/at, Class 0 to 4) that draw up to 25.5 W: IP and PTZ cameras, Wi-Fi 6, 6E and 7 access points, VoIP phones and PoE-powered mini switches. Devices that need PoE++ (802.3bt) or passive PoE are not supported. Devices without PoE work for data only.

For a PoE++ device, look at the Kiwee KB-M3-04, a MoCA 2.5 adapter with up to 90 W per port.

Is PoE over coax the same as Ethernet over coax (EoC)?

Not quite. Ethernet over coax (EoC) only means carrying network data on coax: many basic EoC converters top out at 100 Mbps, and whether they can carry power varies by model. PoE over coax also delivers Power over Ethernet on the same cable.

This kit uses MoCA 2.5 for up to 2.5 Gbps, delivers standard PoE+ (802.3at), switches power on only after it detects the Remote, and can join your home MoCA network through its second coax port.

Is it the same as PoC (power over coax) for HD analog cameras?

No. PoC systems power HD analog cameras (HD-TVI, HD-CVI or AHD) from a PoC recorder or injector, and they only work with matching PoC cameras. This kit carries standard Ethernet and PoE+ instead, so it works with any IP camera and any NVR or network switch.

It is also the simplest way to replace an analog or PoC camera with an IP camera while keeping the same coax.

Can I run an IP camera over old CCTV coax (RG59 or Siamese)?

Yes. Use the RG59 coax of the old CCTV or Siamese cable with the two F-to-BNC adapters in the box. The separate power wires are not needed, because the kit sends power over the coax. RG59 does not reach as far as RG6, so plan for shorter runs.

Is it safe on coax that has other devices on it?

The MoCA PoE OUT port sends 48 V only after it detects the Kiwee Remote, so a TV, modem or analog camera on its own never receives power.

Once the Remote is detected, 48 V is present on the whole cable. Never connect a TV, receiver, cable modem or amplifier directly to the powered run.

Can the same coax carry cable TV or cable internet?

Yes, in D-band (the default). E-band uses the same frequencies as cable TV, so keep D-band on a shared run. Put a DC block in front of every device on that run that isn’t part of the kit, and install a MoCA point-of-entry filter where the cable enters your home. Shops often sell it as a “MoCA POE filter”: that POE means point of entry, not Power over Ethernet.

Never share the run with satellite TV: the receiver’s LNB power conflicts with the 48 V.

Does it work with my MoCA network?

Yes. Connect the Head-End‘s MoCA NO PWR port to your home coax network. In D-band it works with MoCA 2.5 adapters such as the Kiwee KB-M3-02 and KB-M3-03, and with MoCA 2.0 and 1.1 devices at their own speeds. With the E-band firmware on both units, it links to E-band adapters such as the KB-M3-02E.

PoE over Coax Kit or KB-M3-03: which one do I need?

Both carry up to 2.5 Gbps and PoE+ over coax. The difference is where the power comes from. Each KB-M3-03 adapter runs on its own power adapter, so it needs an outlet next to the camera or access point. The PoE over Coax Kit sends 48 V down the coax from the Head-End, so the far end needs no outlet at all.

Choose the kit when there’s no outlet at the device. Choose the KB-M3-03 when there is one, or to add PoE devices at several outlets of a whole-home MoCA network.

Does the kit work in Europe?

Yes. The EU kit ships with an EU-plug 48 V adapter and F-to-IEC adapters, and it is CE compliant. Use an F-to-IEC adapter to connect the data-only MoCA NO PWR port to a TV wall socket; the powered run between the two units must stay a direct coax link with nothing that blocks DC power.

User manuals in German, French, Spanish, Italian, Dutch, Polish, Portuguese and Swedish are in the Downloads section.

Can I install it outdoors?

The Head-End and Remote are indoor units. For an outdoor camera, put the Remote indoors, for example in the attic, the garage or near where the coax enters, and run a short Ethernet cable to the camera.

Can one kit power several cameras?

Each kit is a point-to-point link: one Head-End powers one Remote, and the Remote has one PoE+ port. For several cameras on separate coax runs, use one kit per run.

At one spot, a small PoE-powered (pass-through) switch on the Remote can connect a second camera or device, as long as the switch and everything on it stay within 25.5 W.

Planning several runs as an installer or integrator? Email info@kiwee-broadband.com and we’ll help you plan it.

How do I turn on encryption?

Encryption is off by default for plug-and-play setup. Log in to the Remote’s web interface first (default IP 192.168.144.201; the user manual shows how to connect), open Security settings, enable D-Ext under Network Security Setup and set a password, then save and reboot. Repeat on the Head-End (default IP 192.168.144.200) with the same password.

Who makes the Kiwee PoE over Coax Kit?

Kiwee Broadband, a networking brand headquartered in Las Vegas, Nevada. The same team of telecom and networking engineers makes Kiwee’s MoCA 2.5 adapters, including the KB-M3-02 and KB-M3-03.

Questions go straight to that team at info@kiwee-broadband.com, and we usually reply within 1 business day. Read more in our story.

What warranty and returns do I get?

A 1-year hardware warranty from Kiwee Broadband, plus Amazon’s standard 30-day return window when you buy on Amazon.

Questions before or after you buy? Email info@kiwee-broadband.com. We usually reply within 1 business day.

Buy the Kiwee PoE over Coax Kit

Power + 2.5 Gbps over the coax you already have.

Head-End, Remote, 48 V adapter, cables and BNC adapters. Everything you need is in one box.

  • Fulfilled by Amazon
  • 30-day returns
  • 1-year warranty
  • Replies within 1 business day
Kiwee Broadband PoE over Coax adapter kit: black KB-P3-01H Head-End and white KB-P3-01R Remote Unit
PoE over Coax KitBoth units includedWorks with your setup
Buy on Amazon (opens in a new tab)