KB-M3-05E: MoCA 2.5 Adapter for Satellite TV (4 × 2.5GbE)

KB-M3-05E · E-Band MoCA 2.5 adapter for SAT coaxWired speed over your satellite coax.

Turn the satellite cable already in your walls into a multi-gig wired network — and your satellite TV keeps working. Pre-configured for Extended E-Band (400–900 MHz) out of the box with a built-in 4‑port 2.5GbE switch in every adapter. Up to 2.5 Gbps. No drilling, no new cables.

2 adapters + 4 IEC adapters Fulfilled by Amazon 30-day returns 1-year warranty
EU Edition ·Available on Amazon.de (ships across Europe)

EU kit included: 4 IEC-to-F adapters (2 male, 2 female) for European wall sockets.

Kiwee Broadband KB-M3-05E E-Band MoCA 2.5 adapter 2-pack with four 2.5GbE Ethernet ports, TV and MoCA coax ports, MPS button and DC input
4 × 2.5GbEBuilt-in switch
Satellite TV friendlyExtended E-Band 400–900 MHz
2.5 GbpsMax. over SAT coax*
4 × 2.5GbEPorts per adapter
~1 minSetup, no app
16MoCA devices per network
128-bit AESEncryption via MPS
In short

The KB-M3-05E at a glance

The Kiwee Broadband KB-M3-05E is a 2-pack of E-Band MoCA 2.5 adapters (pre-configured for Extended E-Band 400–900 MHz) with a 4-port 2.5GbE switch in each adapter.

What it is
An E-Band MoCA 2.5 coax-to-Ethernet adapter (factory-set to Extended E-Band 400–900 MHz; 400–700 MHz fallback firmware available) with four 2.5GbE ports, sold as a kit of two.
What it does
Sends wired internet from your router to any room with a SAT coax outlet — up to 2.5 Gbps while your satellite TV keeps working.
Perfect for
Homes with satellite TV (DVB-S/S2), Unicable, loop-through outlets or multiswitches, and fibre, 5G or DSL homes with SAT coax.
Not for
Cable TV / DOCSIS on the same coax (choose KB-M3-05) or DVB-T2 antenna TV (choose KB-G3-05).
Why 4 ports
No extra switch or power brick: three free ports at the router, four in the far room.
Setup
Plug and play in about a minute — no app, no drivers, works with any router. Multiswitch? Use one pair per room.
Why four ports

One coax outlet. Four 2.5GbE devices.

A typical coax adapter gives you a single Ethernet jack — then you buy a switch, find another socket for its power brick and add more cables behind the TV.

The KB-M3-05E puts a 4-port 2.5GbE switch inside every adapter. At the router, three ports stay free for a NAS or PC. In the other room, a gaming PC, console, NAS and mesh Wi-Fi node all plug straight in. Devices on the same adapter talk locally at full Ethernet speed without touching the coax link.

Single-port adapter

  • Adapter + separate switch
  • Two power bricks per room
  • Extra patch cables
  • One more box to fail

KB-M3-05E

  • Switch built in
  • One power adapter
  • 4 × 2.5GbE at both ends
  • One clean box
KB-M3-05E rear panel: four 2.5GbE ports linked to a gaming PC, console, NAS and mesh Wi-Fi node with speed-coded blue and green port LEDs
30-second compatibility check

Will it work in your home?

The KB-M3-05E ships in the Extended E-Band (400–900 MHz), below satellite TV signals. Two quick questions and you’ll know.

1What runs on your coax today?

2How many wired devices in the far room?

Your result

Pick an answer above

We’ll tell you straight away whether the KB-M3-05E fits — or which Kiwee adapter does.

Built different

Everything a satellite home needs, in one box

MoCA 2.5 in the Extended E-Band (400–900 MHz out of the box) runs cleanly below your satellite TV signal — with four 2.5GbE ports on every adapter.

4 × 2.5GbE with built-in switch

Four identical multi-gig ports per adapter. Use any of them for your router or devices; they auto-negotiate 2.5G, 1G, 100M and 10M.

Up to 2.5 Gbps over SAT coax

Pre-configured for Extended E-Band MoCA 2.5 (400–900 MHz) for low-latency wired speed. Standard E-Band (400–700 MHz) fallback firmware is also available if needed.

Satellite TV keeps working

The TV port passes 950–2300 MHz with LNB power and DiSEqC to your receiver. Works with single cable, Unicable (SCR/JESS), loop-through outlets and multiswitches.

Speed-coded port LEDs

Every port shows what’s connected: blue for a 2.5GbE device, green for 1GbE or slower. Spot a slow cable or network card in seconds.

New

Encryption you can see

Turn on 128-bit AES once and copy it to every adapter with the MPS button. A dedicated MPS LED glows green on every encrypted adapter — ideal in flats.

Grows with your home

Up to 16 MoCA devices on one coax network (typically 250–300 m range). Works with E-Band MoCA adapters such as the KB-M3-02E (2 × 2.5GbE) and KB-M3-03E (2.5GbE PoE+).

Interactive tour

Every port on the KB-M3-05E, explained

Tap any part of the rear panel. Then plug in virtual devices and watch the speed-coded LEDs react.

Ethernet 1–4

Four 2.5GbE ports with a built-in switch

All four ports are identical: use any one for your router or your devices. They auto-negotiate 2.5G, 1G, 100M and 10M, and traffic between devices on the same adapter stays local at full Ethernet speed.

Simulate the port LEDs:

PWR

  • Solid green — powered on
  • Off — no power

MoCA

  • Solid green — linked to another adapter
  • Blinking green — data on the coax
  • Off — no other adapter found

MPS

  • Solid green — encrypted (128-bit AES)
  • Off — not encrypted (factory state)
  • All adapters must match

Ports 1–4

  • Blue — 2.5GbE device connected
  • Green — 1GbE / 100M / 10M device
  • Blinking — data; off — idle
Made for real rooms

Where four ports make the difference

Any room with a satellite coax outlet becomes a fully wired room.

Satellite TV in every room? Your SAT coax can carry 2.5 Gbps too.

Standard MoCA overlaps satellite TV. The KB-M3-05E ships on the Extended E-Band (400–900 MHz), safely below the satellite band (950–2300 MHz). Single cable, Unicable and loop-through outlets work as they are — and with a multiswitch, just use one pair per room cable.

Satellite TV (DVB-S/S2)Unicable (SCR / JESS)MultiswitchFibre / FTTH5G & DSL

Gaming room

Console and gaming PC on a wired link with low, steady latency. No more Wi-Fi lag spikes in the middle of a match.

Gaming PCConsoleSmart TVSpare

Home office

Desktop, docking station and NAS on one adapter. Files between your PC and NAS move at full 2.5GbE locally.

Desktop2.5G NASDockIP phone

Mesh & Wi-Fi backhaul

Give a mesh node or access point a wired backhaul over SAT coax, so every floor gets steady Wi-Fi — with three free ports left.

Wi-Fi 7 APPrinterStreamerSpare

Media room

SAT receiver on the TV/SAT socket, plus Smart TV, AV receiver, streamer and console wired from one outlet.

Smart TVAV receiverStreamerConsole

Fibre ONT to router

Fibre box (ONT) in the hallway, router in the living room? Bridge them over coax with a dedicated pair: ONT on adapter A, router WAN on adapter B.

ONT · adapter ARouter WAN · adapter B

Shared flats & apartments

No POE filter exists for the E-Band — turn on 128-bit AES once and copy it with MPS so the green MPS LED confirms your network is private.

128-bit AESMPS LED greenUp to 16 nodes

Port chips show typical link speeds: ● 2.5GbE device   ● 1GbE device.

How it works

Two adapters. The SAT coax in between. That’s the network.

Adapter A sits next to your router. Adapter B goes in any room with a SAT outlet on the same coax. They find each other automatically — while your satellite TV keeps running.

One coax, two jobsFrequencies on the same cable · schematic
MoCA 2.5 Extended E-Band (out of the box)400–900 MHz (Standard 400–700 MHz fallback available)
Satellite TV pass-through950–2300 MHz + LNB power & DiSEqC

Because the Extended E-Band sits below 950 MHz, it leaves the entire satellite band untouched. Cable TV, DOCSIS and DVB-T2 antenna TV also use frequencies below 900 MHz, so they can’t share the same coax. Cable home? Choose the KB-M3-05. Satellite + DVB-T2 on the same cable? Choose the KB-G3-05.

Need more rooms? Add adapters: up to 16 MoCA devices can share one coax network, sharing up to 2.5 Gbps between them (typically 250–300 m of coax — ~15–36% longer reach than D-band).

Works withSatellite TV (DVB-S/S2), Unicable (SCR/JESS), loop-through outlets, multiswitches (one pair per room), fibre/5G/DSL homes with SAT coax, E-Band MoCA adapters (KB-M3-02E, KB-M3-03E)
Not compatible withCable TV or cable internet (DOCSIS) on the same coax, antenna TV (DVB-T2) on the same coax, D-band MoCA adapters (KB-M3-05, KB-M3-02), G.hn adapters
Honest comparison

KB-M3-05E vs Wi-Fi mesh, powerline and a new Ethernet run

The fastest way to get a wired connection into a far room over satellite coax — without drilling.

OptionKiweeKB-M3-05E (E-Band MoCA)Wi-Fi mesh (wireless backhaul)Powerline adaptersNew Ethernet run
Speed to the roomUp to 2.5 GbpsVaries with walls and distanceVaries with wiring and noiseUp to 2.5+ Gbps
LatencyLow and steadyVariableVariableLowest
StabilityShielded SAT coaxInterference-proneAffected by appliancesExcellent
Wired ports in the room4 × 2.5GbEUsually 1–2Usually 1–21 per cable
InstallationPlug and playEasyEasyDrilling, electrician
Keeps your satellite TVYes (950–2300 MHz)———

Which Kiwee coax adapter is right for your home?

Pick based on what runs on your coax and how many ports you need per room.

ModelThis pageKB-M3-05EKB-M3-02EKB-M3-05KB-G3-05
TechnologyMoCA 2.5 (E-Band)MoCA 2.5 (E-Band)MoCA 2.5 (D-band)G.hn Wave 2
Frequency bandExtended 400–900 MHz*Extended 400–900 MHz*1150–1650 MHz2–200 MHz
Ethernet ports4 × 2.5GbE2 × 2.5GbE4 × 2.5GbE4 × 2.5GbE
Max. over coax2.5 Gbps2.5 Gbps2.5 Gbps1.6 Gbps
Satellite TV (DVB-S/S2)Yes (950–2300 MHz)YesNoYes
Antenna TV (DVB-T2)NoNoYesYes
Cable internet (DOCSIS)NoNoYesNo
Best forSAT homes, 3–4 devicesSAT homes, 1–2 devicesCable / DOCSIS homesSAT + DVB-T2 same cable
Where to buyBuy on Amazon.de (opens in a new tab)ViewViewView

* Both KB-M3-05E and KB-M3-02E (plus the PoE+ KB-M3-03E) ship pre-configured for Extended E-Band (400–900 MHz), with Standard E-Band (400–700 MHz) fallback firmware available. They work together on the same coax network when running matching firmware. D-band MoCA (KB-M3-05) and G.hn (KB-G3-05) use different frequencies and do not interoperate with E-Band. Not sure which fits? Read MoCA with Satellite TV or MoCA vs G.hn.

Satellite TV at home and several devices in the room?Complete 2-pack with power supplies, coax & Ethernet cables and 4 IEC adapters.
Buy the 2-pack on Amazon.de (opens in a new tab)
Setup

Online in about a minute

No app, no drivers, no router settings. The adapters link up automatically while your satellite TV keeps working.

Adapter A at the router

Connect your SAT wall outlet (DATA or F socket) to the MoCA port, and a router LAN port to any port 1–4. On F-only outlets, plug your receiver into the TV port.

About 20 s

Adapter B in any room

Connect a SAT outlet on the same coax to the MoCA port. Plug up to four devices into ports 1–4.

About 20 s

Power on and check

After about a minute, PWR and MoCA light green and each port LED shows blue (2.5GbE) or green (1GbE or slower).

About 60 s

Secure it (recommended)

Turn on 128-bit AES once in adapter A’s web page (192.168.144.200), then press MPS on A and on B within 2 minutes. A green MPS LED confirms encryption.

A few minutes
KB-M3-05E setup diagram showing Adapter A at the router and Adapter B in another room over existing satellite coax while satellite TV keeps working
Standard SAT wiring Adapter A at the router · Adapter B in the target room · Satellite TV passes through (950–2300 MHz)Tap diagram to enlarge

Using a multiswitch?

A multiswitch isolates room cables from each other. Place one pair per room cable: adapter A at the multiswitch (between the output and the room cable) and adapter B in the room, then link the A adapters with short Ethernet cables.

Getting the best speed

Use splitters rated 5–2400 MHz (passing 400–900 MHz; 950–2400 MHz SAT-only splitters may block MoCA). Avoid amplifiers between adapters, cap unused splitter outputs with 75 Ω terminators and hand-tighten every F-connector.

KB-M3-05E multiswitch wiring diagram showing one adapter pair per room cable with Adapter A units placed at the multiswitch outputs and linked via Ethernet
Multiswitch setup One pair per room cable · Adapter A at each multiswitch output, linked via Ethernet · Adapter B in each roomTap diagram to enlarge

Multiswitch, wideband LNB or encryption question? Download the KB-M3-05E user guide (PDF)

In the box

A complete two-room EU kit

  • 2×KB-M3-05E adapters
  • 2×Power adapters, 12 V 2 A
  • 2×Coaxial cables
  • 2×Ethernet cables
  • 4×IEC-to-F adapters (2M, 2F)
  • 1×Illustrated English user guide

Includes four push-on IEC-to-F adapters for European wall sockets alongside standard F-type coax connections.

You’ll also need

Before you order

  • A SAT coax outlet in each room on the same coax wiring (or one pair per room cable at a multiswitch)
  • A power socket near each adapter
  • Devices with an Ethernet port — 2.5GbE devices and Cat5e cable or better for full multi-gig speed
  • Splitters rated 5–2400 MHz (passing 400–900 MHz) if splitters sit between outlets
  • No cable TV (DOCSIS) or terrestrial antenna TV (DVB-T2) on the same coax
Specifications

KB-M3-05E technical specifications

ModelKB-M3-05E (sold as a 2-pack)
TechnologyMoCA 2.5 E-Band
Frequency bandExtended E-Band 400–900 MHz out of the box (Standard E-Band 400–700 MHz fallback firmware available)
Coax data rateUp to 2.5 Gbps*, shared by all adapters on the network
Typical coax reachUp to 250–300 m over RG6 coax (75 Ω)
MoCA portF-type (75 Ω), 400–900 MHz
TV pass-through portF-type (75 Ω), 950–2300 MHz with LNB power and DiSEqC
TV pass-through insertion loss≤ 2.5 dB (950–2300 MHz, DC & 22 kHz / DiSEqC pass-through)
Ethernet ports4 × RJ45 2.5GbE, auto-negotiation 2.5G / 1G / 100M / 10M, built-in switch
Devices per networkUp to 16 MoCA devices (typically 250–300 m range); works with Kiwee KB-M3-02E and KB-M3-03E on matching band firmware
Security128-bit AES encryption (off from the factory), MoCA Protected Setup (MPS) with dedicated MPS LED
LED indicatorsPWR, MoCA, MPS (green); Ethernet 1–4 (blue = 2.5GbE device, green = 1GbE / 100M / 10M device)
ButtonsMPS (rear), Reset (underside)
ManagementBuilt-in web page, default address 192.168.144.200
Power input12 V DC, 2 A (power adapter supplied)
In the box2 adapters, 2 power adapters (12 V 2 A), 2 coax cables, 2 Ethernet cables, 4 IEC-to-F adapters (2 male, 2 female), illustrated English user guide
Recommended cablesRG6 coax (75 Ω); Cat5e or better Ethernet
Operating environment0–40 °C (32–104 °F), 10–85% RH non-condensing
Storage environment−20–85 °C (−4–185 °F), 5–90% RH non-condensing
CertificationsCE (EN 55032, EN 55035), RoHS
Warranty1-year limited hardware warranty

* 2.5 Gbps is the maximum MoCA 2.5 network rate. Real-world throughput depends on cable quality, splitters and distance, and is shared by all adapters. A 1GbE device connects at up to 1 Gbps. Page updated November 2026.

FAQ

KB-M3-05E questions, answered straight

Satellite TV & compatibility

Will my satellite TV still work?

Yes. The adapters come pre-configured for Extended MoCA E-Band (400–900 MHz), below the satellite band, and the TV port passes 950–2300 MHz along with LNB power and DiSEqC. Standard Unicable I (EN 50494) operates at 1210–2040 MHz, well above 900 MHz. For dense Unicable II / JESS (EN 50607) setups where User Bands 1–8 start around 975–1075 MHz—or if your picture ever shows blocks or pixelation—email info@kiwee-broadband.com for the Standard E-Band fallback firmware (400–700 MHz), which creates a wide 275+ MHz guard band below 975 MHz.

What is the difference between Extended E-Band (400–900 MHz) and Standard E-Band (400–700 MHz)?

The KB-M3-05E is an E-Band MoCA 2.5 adapter factory-set to Extended E-Band (400–900 MHz) for maximum speed out of the box. You don’t need to change anything unless you see satellite picture pixelation or run a dense Unicable II / JESS (EN 50607) installation with user bands starting around 975–1075 MHz — in that case, switching to the Standard E-Band (400–700 MHz) fallback firmware leaves a 275+ MHz guard band below 975 MHz and eliminates edge interference.

Does it work with a multiswitch?

Yes, with one pair per room cable: a multiswitch does not pass the MoCA network between its outputs. Put adapter A at the multiswitch, between the output and the room cable, and adapter B in the room. For more rooms, add a pair per room cable and link the A adapters with short Ethernet cables.

Which socket of my SAT outlet do I use?

Use the DATA or SAT/DATA socket for the adapter’s MoCA port and keep your receiver on the SAT socket. With an F-only outlet or a bare cable, connect the wall cable to the adapter’s MoCA port and plug your receiver into the adapter’s TV port.

Does it work with European IEC wall sockets?

Yes. The KB-M3-05E kit includes four IEC-to-F adapters (two male, two female) in the box: push the matching one onto your IEC wall socket, then connect the supplied coax cable to the adapter’s MoCA port.

Does it work with cable TV, DOCSIS or DVB-T2?

Not on the same coax. For cable TV or cable internet (DOCSIS), choose the Kiwee KB-M3-05. If satellite and antenna TV (DVB-T2) share one cable, choose the Kiwee KB-G3-05 G.hn adapter.

Can I mix it with other MoCA adapters?

Only with E-Band MoCA adapters, such as the Kiwee KB-M3-02E (2 × 2.5GbE) and KB-M3-03E (2.5GbE PoE+)—make sure all adapters use the same band firmware, either all Extended 400–900 MHz or all Standard 400–700 MHz. D-band adapters such as the KB-M3-02 or KB-M3-05 cannot connect to it.

What if I have a wideband LNB?

Wideband LNBs can output signals starting around 300 MHz, which overlaps the E-Band. Please contact us at info@kiwee-broadband.com before ordering so we can check your setup.

Setup

Do I need two adapters?

Yes — one connected to your router (or at the multiswitch) and one in each room you want to wire. That’s why the KB-M3-05E ships as a 2-pack. You can add more adapters later, up to 16 MoCA devices per network.

Which port do I connect to the router?

Any of them. The four Ethernet ports are identical; the other three work like a switch for devices near your router, such as a NAS, a PC or a game console.

Which coax splitters do I need?

Splitters must pass 400–900 MHz, such as SAT splitters rated 5–2400 MHz. SAT-only splitters rated 950–2400 MHz may block the adapters. Avoid amplifiers between adapters and cap unused splitter outputs with 75 Ω terminators.

Can I use it between my fibre ONT and my router?

Yes, with a dedicated pair: connect the ONT to any port of adapter A and your router’s WAN (internet) port to any port of adapter B. Leave their other Ethernet ports free and keep other MoCA devices off that coax — they would sit outside your router.

Do I have to configure anything?

Usually not: the adapters find each other automatically and work with any router. The built-in web page (192.168.144.200) is only needed to turn on encryption or to load the Standard E-Band fallback firmware (400–700 MHz). If your router uses a different subnet (e.g. 192.168.178.x or 192.168.1.x), temporarily set your computer’s Ethernet IP to 192.168.144.100 (subnet mask 255.255.255.0) to open the web page, then switch back to DHCP.

Speed, ports & security

Is it really 2.5 Gbps over coax?

Up to 2.5 Gbps is the maximum MoCA 2.5 network rate, shared by all adapters on the coax. Real-world speed depends on your cables, splitters and distance. A device on a green (1GbE) port tops out at about 1 Gbps. To measure the coax link itself, use iperf3 with parallel streams (iperf3 -c <IP> -w 1m -P 20 -i 10 -t 5) — an internet speed test only measures your internet plan.

Can I connect more than four devices?

Yes. Connect a network switch to any of the four ports, or add more E-Band adapters — up to 16 MoCA devices per network.

Why is a port LED green instead of blue?

Green means the device connected at 1GbE or slower, which is normal for most TVs and consoles. If the device does have a 2.5GbE port, use a Cat5e or better cable and set its network speed to “Auto”.

How do I turn on encryption?

Encryption is off from the factory. Connect a computer directly to adapter A (if needed, set a temporary static IP such as 192.168.144.100 / 255.255.255.0), open http://192.168.144.200 (admin / maxlinear), go to Security settings, choose Custom under Network Security Setup, set a password, save and reboot. We also recommend changing the default admin / maxlinear web login password after saving your AES key. Then press MPS on that adapter and on each other adapter within 2 minutes. A solid green MPS LED confirms every encrypted adapter.

Buying & support

Where can I buy the KB-M3-05E?

On Amazon.de (opens in a new tab), fulfilled by Amazon with 30-day returns.

What’s in the box?

Two KB-M3-05E adapters, two 12 V 2 A power adapters, two coax cables, two Ethernet cables, four IEC-to-F adapters (two male, two female) and an illustrated user guide in English.

What warranty and support do I get?

A 1-year limited hardware warranty, 30-day returns through Amazon, and direct support from the Kiwee team at info@kiwee-broadband.com. Include your order number, the colour of each LED and how your satellite system is wired (single cable, Unicable or multiswitch).

Manuals & support

Help from the people who build it

KB-M3-05E user guide

Single cable, Unicable, multiswitch wiring, encryption with MPS, web management, Standard E-Band fallback (400–700 MHz) and troubleshooting.

User guide · English (EU kit)PDF · 20 pages · 3.1 MB (opens in a new tab)

Talk to a person

Unicable, multiswitches, wideband LNBs, link speeds — answered by the people who design the adapters, not a script.

info@kiwee-broadband.com

Warranty & returns

1-year limited hardware warranty and a 30-day return window through Amazon. Bought on Amazon? Use Your Orders › Contact seller.

Read the FAQ

Your satellite coax is already in the wall. Make it your fastest network.

Four 2.5GbE ports at each end, up to 2.5 Gbps over SAT coax, and your satellite TV keeps working. Plug in, power on, done.

Buy the 2-pack on Amazon.de (opens in a new tab)
30-day returns1-year warranty4 IEC adapters included

Designed by Kiwee Broadband, the coax-networking specialist behind the first dual-2.5GbE MoCA 2.5 adapter.

KB-M3-05E · E-Band MoCA 2.5 2-pack4 × 2.5GbE per adapter · up to 2.5 Gbps · SAT TV friendly
Buy on Amazon.de (opens in a new tab)