MoCA and DOCSIS 3.1: How to Avoid Interference (D-Band High Setup)

Coax Networking Guide

Short answer: MoCA 2.5 and DOCSIS 3.1 cable modems can share the same coax. The only conflict comes when your provider uses spectrum up to 1218 MHz, which overlaps the bottom of the MoCA D-band. The fix takes minutes: set every MoCA adapter to D-band High (1350–1675 MHz, LOF 1400 MHz), use a PoE filter that passes up to 1218 MHz, and turn off any second MoCA network in your gateway.

By the Kiwee Broadband team, makers of MoCA 2.5 and G.hn Wave 2 coax adapters · Updated October 25, 2026 · 6 min read

Key takeaways

  • Cable systems traditionally stop at 1002 MHz; DOCSIS 3.1 can extend to about 1218 MHz.
  • MoCA 2.5 D-Low (starting just above 1.1 GHz) can overlap that; D-High (1350–1675 MHz) stays clear.
  • Use MoCA-rated splitters (5–1675 MHz) and a DOCSIS 3.1-compatible PoE filter.
  • G.hn coax adapters are not suitable on a line that also carries cable internet.

Where the overlap comes from

MoCA adapters and cable modems were designed to share the same coax: the modem uses the lower part of the cable and MoCA uses the part above it. DOCSIS 3.1, the standard behind most multi-gigabit cable plans, can push the modem’s signal higher up the cable, and in some homes it now touches the bottom of the MoCA range.

Signal on the coaxFrequency rangeOverlap?
Cable TV and internet (classic)Up to about 1002 MHz✅ No overlap with MoCA
DOCSIS 3.1 (extended)Up to about 1218 MHz⚠️ Can overlap MoCA D-Low
MoCA 2.5 D-LowFrom just above 1.1 GHz⚠️ Avoid if DOCSIS reaches 1218 MHz
MoCA 2.5 D-HighAbout 1350–1675 MHz✅ Clear of DOCSIS 3.1
If your provider stops at 1002 MHz, no change is needed.

Signs of a conflict

  • Your internet speed drops or the modem reboots after you add MoCA adapters.
  • The MoCA link is slower than expected or drops from time to time.
  • The modem’s status page shows errors on its highest downstream channels.

Fix 1: move MoCA to D-band High

Kiwee D-band adapters can be set to run only in the upper part of the D-band, well above any DOCSIS 3.1 signal. Do this on every adapter in your network:

  1. Open the adapter’s web interface and go to the MoCA settings.
  2. Set the frequency band to D-band High (1350–1675 MHz).
  3. Set the LOF to 1400 MHz.
  4. Save and restart the adapter, then repeat on the next one.
  5. Check the result: MoCA link lights solid and internet speed back to normal.

All adapters must use the same band and LOF, or they won’t find each other. The KB-M3-03 product page has a step-by-step video of this setup.

Fix 2: use the right splitters and PoE filter

Splitters

MoCA-rated, 5–1675 MHz

Old splitters rated only to 1000 MHz weaken the MoCA signal. Replace them with MoCA-rated ones.

Point-of-entry filter

Passes up to 1218 MHz

Keeps your MoCA signal in and neighbors out, and often improves speed. An older 1002 MHz filter can block part of a DOCSIS 3.1 signal.

Amplifiers

Must pass MoCA

If a drop amplifier sits between rooms, check that it passes MoCA, or the signal will not get through.

Fix 3: check your gateway’s built-in MoCA

Many provider gateways (for example some Xfinity and Cox models) have MoCA built in. If it is switched on, it creates a second MoCA network on the same cable. Either turn the gateway’s MoCA off in its settings and use your adapters on their own, or use the gateway as the first node of your MoCA network, on the same band.

Two separate MoCA networks competing for the same frequencies are a common cause of slow links.

How to check that everything is healthy

Look at the MoCA link rate in the adapter’s web interface. On a good MoCA 2.5 connection it is typically around 3500 Mbps, which gives up to 2.5 Gbps of real throughput. Then run a speed test through the modem to confirm your internet plan speed is unaffected.

Which Kiwee adapters work with DOCSIS 3.1?

All Kiwee D-band MoCA 2.5 adapters coexist with DOCSIS 3.0 and 3.1 cable modems.

2× 2.5GbE

KB-M3-02

Two full-speed devices from one coax outlet.

2.5GbE + PoE+

KB-M3-03

Powers an access point or camera: 30W at the port, up to 25.5W at the device.

2× 2.5GbE + PoE++

KB-M3-04

Up to 90W per port, 120W total, for two high-power devices.

Our G.hn adapters are not suitable for a coax line that also carries cable internet, because G.hn uses the same low frequencies as the modem. See MoCA vs G.hn.

Frequently asked questions

Does MoCA slow down my cable internet?

Not when it is set up correctly. MoCA and the modem use different frequencies. If your provider uses spectrum up to 1.2 GHz, switch the adapters to D-band High to keep them apart.

Do I need a PoE filter?

It is strongly recommended. It protects your network’s privacy, stops interference from neighbors and usually improves MoCA performance. With DOCSIS 3.1, make sure it passes up to 1218 MHz.

How do I know which frequencies my provider uses?

Check your modem’s status page: if it lists downstream channels above 1002 MHz, your provider uses the extended DOCSIS 3.1 range. When in doubt, setting MoCA to D-band High is safe either way.

Does MoCA work with Xfinity?

Yes. MoCA D-band adapters coexist with Xfinity’s DOCSIS 3.1 service on the same coax. If your gateway has MoCA built in, either turn it off or use it as part of your MoCA network, and use D-band High if Xfinity uses spectrum above 1002 MHz in your area.

Still seeing slow speeds?

Send us your modem model and a screenshot of the adapter’s MoCA status page, and we will help you sort it out.

Email info@kiwee-broadband.com

Can You Use MoCA with Satellite TV? DIRECTV and DISH Guide

Coax Networking Guide

Short answer: not with standard MoCA. Standard MoCA 2.5 adapters use the D-band (above 1 GHz), which sits inside the 950–2150 MHz range that satellite TV uses on your coax, so the two interfere. In a DIRECTV or DISH home, use a G.hn Wave 2 coax adapter (2–200 MHz, up to 1.6 Gbps) or an extended E-band MoCA adapter (400–900 MHz, up to 2.5 Gbps) instead.

By the Kiwee Broadband team, makers of MoCA 2.5 and G.hn Wave 2 coax adapters · Updated October 25, 2026 · 5 min read

Key takeaways

  • Satellite TV uses about 950–2150 MHz on the coax; standard D-band MoCA overlaps it.
  • G.hn Wave 2 (2–200 MHz) is the safest choice and works alongside DIRECTV Genie and DISH Hopper systems.
  • Extended E-band MoCA (400–900 MHz) is faster, but can overlap DIRECTV’s own DECA network (about 475–625 MHz).
  • Kiwee options: KB-G3-01 and KB-G3-03 (G.hn), KB-M3-02E (E-band MoCA 2.5).

Why standard MoCA and satellite TV don’t mix

The dish on your roof converts the satellite signal down to a range of roughly 950–2150 MHz and sends it over the coax to your receivers. Standard MoCA 2.5 adapters use the D-band, which sits above 1 GHz, right inside that satellite range. Put the two on the same cable and they interfere: you can lose channels, and the MoCA link becomes slow or unstable.

Second catch: many satellite systems already run their own network over the coax so receivers can share recordings. DIRECTV’s whole-home network (DECA) is itself a MoCA network, in roughly the 475–625 MHz range, and DISH Hopper and Joey receivers also talk to each other over the coax. Any adapter you add must stay clear of those signals too.

Option 1: G.hn over coax (the safest choice)

G.hn Wave 2 works at about 2–200 MHz, far below both the satellite signal and the receivers’ own home network. It delivers up to 1.6 Gbps with very low latency, and Kiwee G.hn adapters have a TV pass-through port (250–2150 MHz) with a built-in diplexer, so your receiver keeps its signal while the adapter carries your data on the same outlet.

G.hn Wave 2 · 2.5GbE

KB-G3-01

Up to 1.6 Gbps over coax for a PC, console, NAS or mesh node, with TV pass-through.

G.hn Wave 2 · PoE+

KB-G3-03

The same link plus PoE+ (up to 30W at the port) to power a Wi-Fi access point or camera.

KB-G3-03 port diagram with compatibility list for satellite TV, DVB-T2, DVB-C and PoE devices
The KB-G3-03 keeps G.hn data at 2–200 MHz and passes satellite TV through its TV port.

One limit: G.hn shares its frequency range with cable internet (DOCSIS) and with some over-the-air VHF channels and FM radio. That rarely matters in a satellite home, but if you also have a cable modem or an antenna on the same coax, ask us first.

Option 2: extended E-band MoCA

MoCA can also run lower on the cable, in the extended E-band (about 400–900 MHz), below the satellite signal. This is the fastest coax option for a satellite home.

MoCA 2.5 · E-band · 2× 2.5GbE

KB-M3-02E

Up to 2.5 Gbps with two 2.5GbE ports, running below the satellite band.

Check first: the E-band can overlap a satellite system’s own home network. A DIRECTV Genie system using DECA, for example, already occupies part of it. If your receivers share recordings over the coax, or you are not sure, choose G.hn, or email us and we will check your setup.

Which adapter should you pick for satellite TV?

Your situationBest choice
Satellite TV, receivers linked over coax (DIRECTV Genie, DISH Hopper/Joey)G.hn: KB-G3-01 or KB-G3-03
Satellite TV, single receiver, no whole-home networkExtended E-band MoCA (KB-M3-02E) for top speed, or G.hn
You need to power an access point or cameraG.hn with PoE+: KB-G3-03
Satellite cancelled, coax now unusedOnce the dish equipment is removed and the satellite splitters are replaced with MoCA-rated ones, standard D-band MoCA (KB-M3-02) is the fastest
Not sure which row fits? Email us your provider and receiver models.

How to set up Ethernet over coax in a satellite home

  1. Place the first adapter near your router. It needs a coax outlet connected to the same coax network as the rooms you want to reach.
  2. Keep the receiver on the TV pass-through port. Where an adapter shares an outlet with a satellite receiver, connect the wall to the adapter’s coax input and the receiver to its TV port, so both keep working.
  3. Don’t remove satellite parts you don’t understand. Multiswitches, SWM splitters and power inserters feed the dish. Leave them in place and work around them.
  4. Use the same technology on every adapter. G.hn adapters don’t talk to MoCA adapters, and E-band MoCA doesn’t talk to D-band MoCA.
  5. Turn on encryption. Pair the adapters with their push button so the network is encrypted.

Frequently asked questions

Can I use regular MoCA adapters with DIRECTV?

Standard D-band MoCA adapters overlap the satellite signal and are not recommended. DIRECTV’s own DECA adapters run an older, slower MoCA network for the receivers. For your own Ethernet network, use G.hn.

Does MoCA work with DISH Hopper?

Standard D-band MoCA is not recommended with DISH, because it overlaps the satellite signal on the coax. Hopper and Joey receivers also talk to each other over the coax. G.hn adapters, which run at 2–200 MHz, are the safest way to add Ethernet over the same cable.

Will a G.hn adapter affect my satellite picture?

No. Its data sits at 2–200 MHz, far below the satellite signal, and the TV port passes the satellite signal through.

How fast is Ethernet over coax in a satellite home?

Up to 1.6 Gbps with G.hn Wave 2, or up to 2.5 Gbps with extended E-band MoCA 2.5. Both are well beyond what most Wi-Fi delivers through walls and floors.

Not sure what your satellite system is running?

Send us your provider and receiver models and we will tell you which adapter fits.

Email info@kiwee-broadband.com

MoCA vs G.hn: Which Coax Ethernet Adapter Should You Use?

Coax Networking Guide

Short answer: MoCA 2.5 and G.hn both turn the coax in your walls into wired Ethernet. Use MoCA 2.5 (D-band) if you have cable internet such as Xfinity, Spectrum or Cox: it is faster (up to 2.5 Gbps) and shares the cable with your modem. Use G.hn Wave 2 if you have satellite TV such as DIRECTV or DISH: it runs at 2–200 MHz, below the satellite signal, at up to 1.6 Gbps. If your coax is unused, either works and MoCA is faster.

By the Kiwee Broadband team, makers of MoCA 2.5 and G.hn Wave 2 coax adapters · Updated October 25, 2026 · 6 min read

Key takeaways

  • MoCA 2.5: up to 2.5 Gbps, runs above 1 GHz, works alongside DOCSIS cable internet, conflicts with satellite TV.
  • G.hn Wave 2 over coax: up to 1.6 Gbps, runs at 2–200 MHz, works alongside satellite TV, conflicts with cable internet.
  • MoCA and G.hn adapters cannot talk to each other: use one technology for the whole network.
  • Satellite homes can also use extended E-band MoCA (400–900 MHz), such as the Kiwee KB-M3-02E.

What is the difference between MoCA and G.hn?

MoCA (Multimedia over Coax Alliance) and G.hn (ITU-T G.9960/G.9961) both send Ethernet over the coax cable already in your home. They look alike from the outside, a small box with a coax jack and an Ethernet port, but they use very different parts of the cable, and that decides which one will work in your home.

A coax cable can carry many signals at once, as long as each uses its own frequency range. Cable internet, cable TV, satellite TV and antenna TV each have their own range, and a coax network adapter has to fit into the space that is left free in your home.

Above 1 GHz

MoCA 2.5 (D-band)

Sits just above cable TV and DOCSIS cable internet. Designed to share the cable with your cable modem. Up to 2.5 Gbps.

2–200 MHz

G.hn Wave 2 (coax)

Runs far below satellite TV (950–2150 MHz) and most antenna channels, but overlaps cable internet. Up to 1.6 Gbps.

So the two are mirror images: MoCA D-band coexists with cable internet but collides with satellite TV, while G.hn coexists with satellite TV but collides with cable internet.

MoCA vs G.hn comparison table

MoCA 2.5 (D-band)G.hn Wave 2 (coax)
Max throughputUp to 2.5 GbpsUp to 1.6 Gbps
Frequency rangeAbove 1 GHz (D-band)About 2–200 MHz
Cable internet (DOCSIS)✅ Works alongside❌ Not on the same cable
Satellite TV❌ Overlaps satellite signals✅ Works alongside
Antenna TV✅ Works alongside⚠️ UHF yes; some VHF and FM overlap
LatencyLow, a few millisecondsVery low (under 1 ms on Kiwee G.hn adapters)
Devices per networkUp to 16Up to 16
SecurityLink encryption, push-button pairingAES-128, push-button pairing
StandardMoCA AllianceITU-T G.9960 / G.9961
MoCA 2.5 vs G.hn Wave 2 over coax, based on Kiwee adapter specifications.

Which one should you use?

Pick the scenario that matches what already runs on your coax.

Cable internet

Xfinity, Spectrum, Cox, Optimum: use MoCA

Your modem uses the low and middle part of the coax and MoCA sits above it, so you get up to 2.5 Gbps between rooms with the modem untouched. On DOCSIS 3.1, see our MoCA and DOCSIS 3.1 guide.

Models: KB-M3-02 (2× 2.5GbE), KB-M3-03 (PoE+), KB-M3-04 (2× PoE++).

Satellite TV

DIRECTV, DISH: use G.hn or E-band MoCA

G.hn stays far below the satellite band and Kiwee G.hn adapters pass the TV signal through untouched. Details in our MoCA and satellite TV guide.

Models: KB-G3-01 (G.hn), KB-G3-03 (G.hn + PoE+), KB-M3-02E (E-band MoCA).

Fiber or DSL

Unused coax: either works

MoCA 2.5 gives the highest speed; G.hn the lowest latency. MoCA keeps working if you later switch to cable. Verizon Fios TV boxes run their own MoCA network, so check first.

Antenna TV

Over-the-air TV: MoCA is the safe choice

Broadcast TV stays far below the MoCA D-band. G.hn works with UHF, but some VHF channels and FM radio share its range.

Can you mix MoCA and G.hn adapters?

No. MoCA adapters only talk to MoCA adapters, and G.hn adapters only talk to G.hn adapters, so buy all the adapters for one network in the same technology. Within MoCA, a MoCA 2.5 adapter works with older MoCA 2.0 or 1.1 devices on the same band, but the link runs at the speed of the slowest device.

Checklist before you buy

  1. Find out what runs on your coax today: cable internet, cable TV, satellite TV, antenna TV, or nothing.
  2. Match the technology: cable internet on the same coax means MoCA D-band; satellite TV means G.hn or extended E-band MoCA.
  3. Count your rooms: one adapter next to your router, plus one in each room you want to connect.
  4. Need power too? Pick a PoE model (KB-M3-03, KB-M3-04 or KB-G3-03) to power an access point or camera.

Frequently asked questions

Is G.hn better than MoCA?

Neither is better everywhere. MoCA 2.5 is faster (up to 2.5 Gbps versus 1.6 Gbps) and shares the cable with cable internet. G.hn has lower latency and shares the cable with satellite TV. The right choice depends on what else runs on your coax.

Can I use G.hn with Xfinity or Spectrum internet?

Not on the same coax as the cable modem, because G.hn and cable internet use overlapping frequencies. Use MoCA D-band adapters instead.

Can I use MoCA with DIRECTV or DISH?

Standard D-band MoCA overlaps the satellite signal, so it is not recommended. Use G.hn adapters or an extended E-band MoCA adapter.

Is G.hn over coax the same as powerline?

They use the same G.hn standard, but over coax the signal travels on shielded cable instead of noisy power lines, so speeds are much higher and more consistent. Coax and powerline G.hn adapters are separate products.

How many adapters do I need?

At least two: one next to your router and one in each room you want to connect. Both MoCA and G.hn support up to 16 adapters on one network.

Not sure which one fits your home?

Tell us what runs on your coax and we will recommend the right Kiwee adapter.

Email info@kiwee-broadband.com

KB-M3-03 Now Available: The MoCA 2.5 Adapter with Built-In PoE+

The Kiwee KB-M3-03 is now available on Amazon. It is the first MoCA 2.5 adapter with integrated PoE+: it turns the coax already in your walls into a 2.5 Gbps wired link and powers the device on the other end of its Ethernet cable, such as a Wi-Fi access point, IP camera or VoIP phone.

Kiwee KB-M3-03 MoCA 2.5 adapter with 2.5GbE PoE+ port

Data and power from one adapter

  • 2.5 Gbps over coax: MoCA 2.5 in D-band, with a 2.5GbE Ethernet port, for streaming, gaming and mesh backhaul.
  • PoE+ (IEEE 802.3at): 30W at the port, up to 25.5W at the device, also compatible with 802.3af. No outlet or power brick needed at the access point, camera or phone.
  • Plug and play: connect the coax, the adapter’s power supply and the Ethernet cable. No software or configuration for typical setups.
  • Works with cable internet: coexists with DOCSIS modems and cable TV through a built-in TV pass-through port.
KB-M3-03 delivering data and PoE+ power over existing coax

Who it’s for

  • Wi-Fi upgrades: mount a Wi-Fi 6, 6E or 7 access point where coverage is worst, not where the sockets are.
  • Security cameras: power a PoE camera in the garage, attic or eaves over the coax that’s already there.
  • Home offices and small businesses: VoIP phones and access points without new cable runs.
KB-M3-03 use cases: access points, IP cameras and VoIP phones

Key specifications

MoCA standardMoCA 2.5 (D-band, 1125–1675 MHz), backward compatible with 2.0 / 1.1 / 1.0
Ethernet1 × 10/100/1000/2500 Base-T with PoE+
PoE outputIEEE 802.3at: 30W at the port, 25.5W at the device (802.3af compatible)
Max throughputUp to 2.5 Gbps (iperf-verified)
TV pass-through5–1002 MHz
Network sizeUp to 16 devices
SecurityMoCA link encryption with MPS pairing
ChipsetsMaxLinear MxL3710 + GPY211
RegulatoryFCC, CE
Warranty1 year, plus 30-day returns through Amazon
KB-M3-03 PoE+ output detail

Need more ports or more power?

For two devices at once, the KB-M3-04 has two 2.5GbE ports with PoE++ (up to 90W per port, 120W total). For homes with satellite TV, see the KB-G3-03 G.hn adapter with PoE+.

Questions before you buy? Email info@kiwee-broadband.com.

Dual 2.5GbE MoCA 2.5: Why Two Ports Beat One

Coax Networking Guide

Short answer: a dual-port MoCA 2.5 adapter gives you two full 2.5GbE connections from one coax outlet, so a PC and a console, or a router and a mesh node, both get wired speed without an extra switch. The Kiwee KB-M3-02 (D-band) and KB-M3-02E (E-band, for satellite-TV homes) are the only MoCA 2.5 adapters with two 2.5GbE ports.

Buy on Amazon

By the Kiwee Broadband team · Updated October 25, 2026 · ★ 4.7 on Amazon · 5 min read

Key takeaways

  • 2.5 Gbps real-world throughput over coax (iperf-tested), with only 3–4 ms of added latency.
  • Two 2.5GbE ports per adapter: no extra switch for a second device.
  • Plug and play, with a TV pass-through port. FCC and CE compliant.

Wi-Fi wasn’t built for what you’re asking it to do

Gamers

Ping spikes at the worst moment

Packet loss in overtime, lag in the final circle. No router upgrade fully fixes physics.

4K/8K streamers

Buffering when the house gets busy

Every phone, laptop and console competes for the same crowded airwaves.

Remote workers

Frozen calls, crawling uploads

When your income depends on your connection, “usually fine” isn’t fine.

Ethernet fixes all of this, but running new cable through finished walls costs hundreds of dollars and days of mess. There’s a third option already installed in your home: the coax cable behind your TV.

How it works: the network hiding in your walls

  1. Connect at the router. Screw one adapter onto the coax jack near your router and link them with an Ethernet cable.
  2. Connect in any room. Screw a second adapter onto any other coax jack: bedroom, office, den.
  3. Plug in and play. Plug your devices into the Ethernet ports. Your TV signal keeps working through the built-in pass-through port.

MoCA 2.5 D-band runs above the frequencies your TV and cable modem use, so everything coexists on the same cable. On DOCSIS 3.1, see MoCA and DOCSIS 3.1.

Kiwee MoCA 2.5 adapter connected to coax and Ethernet in a home setup

Why two ports change the math

No switch

Two devices, one box

Feeding a PC and a console from a single-port adapter means buying a 2.5G switch: another $30–60, another power brick, another box on the shelf.

Full backhaul

Use the whole link

The MoCA 2.5 link carries roughly 3 Gbps in total. Two ports share it, so a NAS backup runs at full speed while you game.

Router room

One box does two jobs

One port to your router, one to a mesh node or desktop, right where internet enters your home.

Future-proof

Room to grow

Multi-gig plans, 8K streams, a home server: when the second device arrives, the port is already there.

MoCA 2.5 vs the alternatives

Kiwee dual-port MoCAWi-Fi meshPowerlineNew Ethernet runs
Real-world speed✅ 2.5 Gbps, consistentVaries with walls and congestionDepends on electrical wiring✅ Up to 10 Gbps
Latency and stability✅ Wired-grade, +3–4 msFluctuates under loadInconsistent✅ Best possible
Installation✅ Screw onto existing coax✅ Easy✅ Easy❌ Invasive and costly
Uses existing wiring✅ Yes, your coax—Yes, electrical❌ No, new cable
Devices per adapter✅ 2 (dual port)—Usually 11 per run

Which Kiwee adapter is right for your home?

Cable internet or antenna TV: D-band (KB-M3-02). Satellite TV: E-band (KB-M3-02E). Powering an access point or camera: PoE+ (KB-M3-03). Both dual-port models share the same design; only the operating band differs.

Most popular · D-band

KB-M3-02

2× 2.5GbE. Works with cable internet (DOCSIS), cable TV and antenna. TV pass-through.

Satellite homes · E-band

KB-M3-02E

2× 2.5GbE, extended E-band (400–900 MHz), below the satellite signal. TV pass-through.

PoE+ · D-band

KB-M3-03

1× 2.5GbE with PoE+: powers access points and cameras over the Ethernet cable.

Technical specifications

KB-M3-02 (D-band)KB-M3-02E (E-band ext.)
Ethernet2 × 10/100/1000/2500Base-T2 × 10/100/1000/2500Base-T
MoCA bandD-band, 1150–1650 MHzE-band extended, 400–900 MHz
MoCA standardMoCA 2.5 / 2.0MoCA 2.5 / 2.0
TV pass-throughYes (5–1002 MHz)Yes (950–2300 MHz)
Works withCable internet (DOCSIS), CATV, antennaSatellite TV homes
Not compatible withSatellite TV, MoCA E-bandDOCSIS, CATV, MoCA D-band
Network sizeUp to 16 devicesUp to 16 devices
ChipsetsMaxLinear MxL3710 + GPY211MaxLinear MxL3710 + GPY211
CertificationsFCC, CEFCC, CE
Interoperates with goCoax, Actiontec and ScreenBeam MoCA adapters (network speed follows the slowest adapter).

Frequently asked questions

Do both ports really run at 2.5 Gbps at the same time?

Yes. Both ports can run at 2.5 Gbps simultaneously, sharing the total MoCA 2.5 bandwidth of approximately 3 Gbps.

What’s the difference between the KB-M3-02 and KB-M3-02E?

Same dual-port design, different band. The KB-M3-02 uses D-band for homes with cable internet or antenna TV; the KB-M3-02E uses extended E-band for homes with satellite TV. Pick by your TV service.

Will it work with my DOCSIS 3.1 cable modem?

Yes. If your provider uses spectrum up to 1.2 GHz, set the adapters to D-band High with an LOF of 1400 MHz. See MoCA and DOCSIS 3.1.

Does it work as wired backhaul for eero, Orbi or UniFi mesh?

Yes. It gives each node a stable wired link that outperforms wireless backhaul, with any mesh system that supports Ethernet backhaul.

How much latency does it add for gaming?

Only 3–4 milliseconds, far lower and steadier than Wi-Fi.

Your coax is already installed. Use it.

Multi-gigabit wired networking for two devices per room, set up in minutes. ★ 4.7 on Amazon.

Buy on Amazon